Titan esc-40a

Need help with programing.
Can enter programing mode.
I know from trial and error that 1long 3short =motor reversing,this is the ninth possible option .
Followed by 3long which is exit prog mode.
The esc emits 3 ascending tones when initialized and ready.
Cant find any programing info, and wont fly without it for fear of burning esc,motor etc.
Any help would be greatly appreciated.
Thanks
_________________
Mark


Yes Dear , I'll mow the grass as soon as i get this one last flight in.( or learn to fly inverted!!!)

DX6i
Honey Bee CPX(sold)
Blade MSR
Blade mCP X
Titan 450v2 (trex450sev2 clone)

Have you looked on the Thundre Tiger website for the manual?

http://www.tiger.com.tw/manual/1__6__1.html
_________________
René

CloggieCopter™ (Tarot) 450 Pro, Align 450M, HW Platinum Pro 40A, D12-MG, Assan GA-250 + HSG-5084MG
CloggieCopter™ (Tarot) 500 ESP, AX Typhoon 500H, HW Platinum Pro 80A, MG930, Quark + DS520
Futaba T7CH, R617FS and FrSky TFR8-S

Right click, or Save As, or Copy Image, and you'll see the right page too. It's just Heliguy can't display the whole thing.


Last edited by buzzbird on Tue Apr 05, 2011 4:41 pm; edited 3 times in total

It's now in the Manuals section here http://www.heliguy.com/i/bl40.JPG

Thanks for the fast responces , but this is not mini titan. It is titan v2 by koko technologies. A chinese trex clone.
Esc is " Titan esc-40a" model no. F410.
Thanks for your time.

Mark
_________________
Mark


Yes Dear , I'll mow the grass as soon as i get this one last flight in.( or learn to fly inverted!!!)

DX6i
Honey Bee CPX(sold)
Blade MSR
Blade mCP X
Titan 450v2 (trex450sev2 clone)

Best I can find is the sales page for that esc on Koko's site, with some contact details but no mention of a manual. You may have to email them.

Dude, I have the same ESC but each time I follow the instruction into get to programming mode, I just does its normalisation beeps.
How do u get into programming mode?

To enter programming mode, turn on tx and move throttle to max.
Throttle hold must be off.
For safety , remove main blades, dont unplug motor as it emmits the tone you need to hear.
With tx on, throttle at max, plug in heli.
You will hear a warning tone followed about 10 secs. Later by programming tone.
Tones will then cycle for each programable feature.
These are the ones I know.
One short = brake mode
One long+ four short = motor reversing
Three long= exit programming mode

The init tones indicate esc arming, battery cell count(three beeps for 3s lipo) , and final ascending scale to indicate heli is ready.

I have found by trial and error that my heli will function properly with all options set to option one . I cant seem to find "very soft start" or "gov".

In triing to find what each setting is , I had heli in low hover and intentionaly flew to LVC , had fourth paramiter on third setting , when it hit LVC it abruptly powered off and fell from the air, so be carefull in changing things when not sure.
Changing lvc action , timing , batt type , etc could have harmfull results.
_________________
Mark


Yes Dear , I'll mow the grass as soon as i get this one last flight in.( or learn to fly inverted!!!)

DX6i
Honey Bee CPX(sold)
Blade MSR
Blade mCP X
Titan 450v2 (trex450sev2 clone)