Spartan Quark problems

5 posts   •   Page 1 of 1
User avatar
waqr
Senior Pilot
 
Posts: 150
Joined: Sat Jan 01, 2011 7:39 am
Location: Sweden

Spartan Quark problems

by waqr » Fri May 25, 2012 7:42 am

Thanks!

Was looking at the tail this morning and when the tail pitch slider is in the middle (in rate mode) I only get like 2-3 degrees of pitch (servo arm at 90 degrees) and according to the manual I should have like 8 degrees. Will this be a problem and how can this be resolved? Lenghtening and shortening the rod will only move the pitch slider back and forth from midposition on the tailshaft.

Also, I set the endpoints in the gyro yesterday but today I noticed that when I flip between rate and HH mode my end points are different. In rate mode the endpoints are perfect with no servo binding but when I switch to HH mode the servo binds in one direction which means that I have to adjust the travel adjustment in the radio again. However when switching to rate mode the I have to increase the same value again in order to reach full pitch.

I have made the setup twice all according to the manual so I can`t have done something wrong here........

Please help!
Skya 450 Pro (Align 450 Pro clone)

User avatar
yoshimoto
Group Captain
 
Posts: 1335
Joined: Sun Jan 11, 2009 6:42 am
Location: Newcastle.

Quark query...

by yoshimoto » Sun May 27, 2012 6:02 pm

I dont set end points on the radio,i just leave this between 100-120 and only set end points in the gyro menu with the Quark.
Basically give the radio full tail travel and let the gyro limit it.
Yoshi :wink:
Gaui H200V2.Twisted Hobbies Crack Bipe.Heliguy Viper.Solo Pro 125.DJI F450.Turnigy 9X V2+9XR,Turnigy and Orange RX modules.
Phoenix,GT85 and plain old luck.

User avatar
randalsh
Air Vice Marshal
 
Posts: 21043
Joined: Sat Feb 09, 2008 12:09 pm
Location: Rutland, Leicestershire

by randalsh » Sun May 27, 2012 6:51 pm

The endpoints should be the same in either mode with the Quark :?
Are you sure you have the travel adjust the same in both modes on your tx?
Randal

CHARLEY, the Rock and the Hard Place

https://www.smashwords.com/books/view/382610




Trex 450 SE. 65mgs & 401
Trex 450 Pro. Fbl. Spartan VX1e.
DX7
mCPx.
Phoenix.

User avatar
waqr
Senior Pilot
 
Posts: 150
Joined: Sat Jan 01, 2011 7:39 am
Location: Sweden

by waqr » Sun Jun 03, 2012 4:41 am

Problem solved. I made the setup again and now it works fine....

Thanks guys!
Skya 450 Pro (Align 450 Pro clone)

User avatar
randalsh
Air Vice Marshal
 
Posts: 21043
Joined: Sat Feb 09, 2008 12:09 pm
Location: Rutland, Leicestershire

by randalsh » Sun Jun 03, 2012 6:49 am

Although the Q is easy to set up, it's just as easy to set up wrong :wink:

Good to see you sorted it :)
Randal



CHARLEY, the Rock and the Hard Place



https://www.smashwords.com/books/view/382610









Trex 450 SE. 65mgs & 401

Trex 450 Pro. Fbl. Spartan VX1e.

DX7

mCPx.

Phoenix.

5 posts   •   Page 1 of 1

Who is online

Users browsing this forum: No registered users and 0 guests

It is currently Sat Jul 04, 2015 4:00 am